Toolbar
Icon |
Mouse
Cursor |
Description |
|
|
DYNAMIC 3D VIEW
This command makes it possible to rotate the features around
two axes in 3D space. The primary rotation axis is around an axis
that extends out from graphics view port directly at you. The
secondary rotation axis is along the X-Axis of the graphics view
port which starts at the center of the display and points right.
To begin the DYNAMIC 3D VIEW operation hold down the left
mouse button. Dragging the mouse toward the right or left will rotate about
the primary rotation axis. Dragging up or down will rotate about
the secondary axis. Combining the two moves will result in the
ability to rotate the current view to any orientation.
To constrict the rotation to specific angles, hold the
<shift> key down on the keyboard while dragging. Rotation will
take place only in fixed angle increments. The default for this
angle is 15° and can be set to any value in
System
Options.
|
|
|
ZOOM IN
When the ZOOM IN command is activated, the mouse cursor
changes to the plus magnifying symbol until you select the ZOOM
IN command again, or any other graphic command.
When you position the mouse over an area within your graphics
and press the left mouse button, the graphics will center on the
mouse click and zoom in.
The amount of zoom control is determined by a setting in
System
Options.
|
|
|
ZOOM OUT
When the ZOOM OUT command is activated, the mouse cursor
changes to the minus magnifying symbol until you select the ZOOM
OUT command again, or any other graphic command.
When you position the mouse over an area within your graphics
and press the left mouse button, the graphics will center on the
mouse click and zoom out.
The amount of zoom control is determined by a setting in
System
Options.
|
|
|
ZOOM ALL
The ZOOM ALL command permits you to see all features in the
current view. It performs a calculation to determine the full
extent, then redraws the display.
In some cases, you may have solutions or features that are at
a extreme distance to the core features within your inspection
report. When you perform a ZOOM ALL, these are included often
resulting in display of unrecognizable features. To control this
behavior, you can select individual features to be excluded from
the ZOOM ALL extent calculation, see
Feature Properties.
|
|
|
FIT TO SELECTED
The FIT TO SELECTED command permits you to view
all the selected features fitted to the extents of your display.
When you perform this fit command, you also
center the rotation axis to the center of the display providing
local rotation behavior using the Rotate Tool.
|
|
|
REGENERATE
Selecting the REGENERATE tool, will command the graphic
engine to redraw all features within the inspection report.
|
|
|
ZOOM WINDOW
The ZOOM WINDOW tool is used to create a view box to show
only a portion of the current view. The results of this is a
ZOOM IN and PAN to the view box you have created.
To create the view box, select the ZOOM WINDOW command. You
mouse cursor will change to the ZOOM WINDOW cursor. Move your
mouse to one corner where you want the view box to start. While
holding down the left mouse button, move the mouse to the
opposite view box corner. You will see a box being drawn with
your movements. When you release the left mouse button, the
graphics area will be redrawn to the view box.
|
|
|
WINDOW SELECT
This command is used to select features in the graphic area
that a view box touches. The selection process is determined by
the current style, wireframe or solid.
To create the view box, select the WINDOW SELECT command and
follow the instructions for ZOOM WINDOW.
In wireframe mode, when you release the left mouse button,
all features the the view box touches will be highlighted both
in the graphic area and the report area.
In solid mode, when you release the left mouse button, the
closest feature to your viewpoint will be highlighted. This is
often desirable when there are features that can not be seen
behind the front most features.
|
|
|
GRAPHIC SETTING TOOL
The Graphic Setting Tool provides a one-stop tool
to control the visible state of the features, stylus position,
reference sphere and surface plate states.
|
|
|
ZOOM SCALE
The ZOOM SCALE command is activated by holding down the
<Ctrl + shift> on the keyboard when your mouse is over the
graphics area. Then, when you press the left mouse button, the
mouse cursor changes to the ZOOM SCALE cursor. Moving your mouse
to the right perform a ZOOM IN and moving to the left is a ZOOM
OUT.
|
|
|
DYNAMIC PANNING
To quickly reposition the view within the graphics area, hole
the <Ctrl> key down on the keyboard while you mouse is
over the graphics area. The mouse cursor will change to the
DYNAMIC PAN symbol and any movement with the mouse will
reposition the displayed features.
|